Home » Forums » Community Edition » Help

Sangoma A101 with E&M Wink PRI

johnsr4
Posts: 9
 Member Since:
2008-03-25
Submitted by johnsr4 on Mon, 06/30/2008 - 9:51am.

I am getting a busy signal when dialing into my new Trixbox system with an PRI. when I do a wanrouter status it shows "connected" and the carrier says he is able to see that my D channel is idle. We can't dial out though, and dialing in always gets a busy signal. I have a g0 ZAP trunk group configured. I've run through setup-sangoma, zaptel and zapata usuals. How do I determine what "context" I need to enter in the zapata.conf file? Also-I had the carrier tell me that signalling was E&M Wink.

Any help is GREATLY appreciated. Here are the specs:

Trixbox 2.6.1.1
Sangoma AFT A101SH single port PRI card
wanpipe release 3.2.5

/etc/zaptel.conf
------------
loadzone=us
defaultzone=us

#Sangoma A101 port 1 [slot:1 bus:9 span:1]
span=1,0,0,esf,b8zs
e&m=1-24

the bottom part of /etc/asterisk/zapata.conf shows:
---------------------------------------------------------

;Sangoma A101 port 1 [slot:1 bus:9 span:1]
context=from-pstn
group=0
signalling=em_w
channel => 1-24

wancfg - I have 'protocol' set to TDM Voice.

Thanks

-John

‹ Remote Extension Configuration Remote Aastra 9133 Timing out? ›

&nbsp

johnsr4
Posts: 9
 Member Since:
2008-03-25
log file note
Mon, 06/30/2008 - 10:06am

almost forgot -- I also noticed the following lines in my /var/log/asterisk/full log file

Jun 30 12:03:59] VERBOSE[31716] logger.c: -- AGI Script dialparties.agi completed, returning 0
[Jun 30 12:03:59] DEBUG[31716] app_macro.c: Executed application: AGI
[Jun 30 12:03:59] VERBOSE[31716] logger.c: -- Executing [s@macro-dial:7] Dial("Zap/24-1", "SIP/2160||tr") in new stack
[Jun 30 12:03:59] WARNING[31716] app_dial.c: Unable to create channel of type 'SIP' (cause 3 - No route to destination)
[Jun 30 12:03:59] VERBOSE[31716] logger.c: == Everyone is busy/congested at this time (1:0/0/1)


&nbsp

nothings_found
Posts: 106
 Member Since:
2007-03-10
You can't have an E&M wink
Mon, 06/30/2008 - 11:56am

You can't have an E&M wink PRI. The line is either a Digital PRI with full 23 channels OR a Analog Trunk with full 24 channels.

Contact your carrier and verify which one is it.


&nbsp

johnsr4
Posts: 9
 Member Since:
2008-03-25
PRI troubleshooting....continued
Tue, 07/01/2008 - 8:01am

Ok - Now I am really confused.

I spoke with the carrier and confirmed that it is an NI2 PRI, but they still said that the signalling type is wink start. when I run setup-sangoma I assume I should now select PRI CPE instead of E&M Wink? How does/should this affect my zapata.conf file (i.e.: context=??)

Thanks


&nbsp

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.