Can't make X100P FXO work in TrixBox

Thanks...okay, I'm guessing from the bottom outputs maybe it's not configured correct? I've rebuilt and reconfigured it a number of times and then tried a number of fixes... so I'm not sure what state things are in now.....

If you can point me to the right fix that would be great...

lspci:

00:00.0 Host bridge: Intel Corporation 82810E DC-133 GMCH [Graphics Memory Controller Hub] (rev 03)
00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 CGC [Chipset Graphics Controller] (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02)
00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801AA IDE (rev 02)
00:1f.2 USB Controller: Intel Corporation 82801AA USB (rev 02)
00:1f.3 SMBus: Intel Corporation 82801AA SMBus (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio (rev 02)
01:07.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 34)
01:08.0 Communication controller: Motorola Wildcard X100P

lsmod:

Module Size Used by
md5 4033 1
ipv6 235137 14
autofs4 24773 0
i2c_dev 11329 0
i2c_core 22081 1 i2c_dev
sunrpc 162725 1
ztdummy 3924 0
wctdm 34880 0
wcfxo 13088 0
wcte11xp 27936 0
wct1xxp 19488 0
wct4xxp 65600 0
tor2 91936 0
zaptel 206852 9 ztdummy,wctdm,wcfxo,wcte11xp,wct1xxp,wct4xxp,tor2
crc_ccitt 2113 1 zaptel
dm_mirror 27825 0
dm_mod 57556 1 dm_mirror
button 6481 0
battery 8901 0
ac 4805 0
uhci_hcd 31065 0
hw_random 5845 0
snd_intel8x0 33897 0
snd_ac97_codec 63889 1 snd_intel8x0
snd_pcm_oss 49017 0
snd_mixer_oss 17985 1 snd_pcm_oss
snd_pcm 96841 2 snd_intel8x0,snd_pcm_oss
snd_timer 29893 1 snd_pcm
snd_page_alloc 9673 2 snd_intel8x0,snd_pcm
snd_mpu401_uart 8769 1 snd_intel8x0
snd_rawmidi 26597 1 snd_mpu401_uart
snd_seq_device 8137 1 snd_rawmidi
snd 55461 9 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 9889 1 snd
3c59x 39293 0
mii 5185 1 3c59x
floppy 58481 0
ext3 116809 2
jbd 71385 1 ext3

No zaptel but zaptel.conf? :

# Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#

# It must be in the module loading order

# Span 1: ZTDUMMY/1 "ZTDUMMY/1 1"

# Global data

loadzone = us
defaultzone = us

proc:

Span 1: ZTDUMMY/1 "ZTDUMMY/1 1"

Oops. It was listed as /etc/zaptel initially but here is the one from /etc/sysconfig/ --I did check to see that it wasn't commented out and have run genzapconfig a few times:

TELEPHONY=yes
#DEBUG=yes

# Un-comment as per your requirements; modules to load/unload
# genzaptelconf will populate this file

#Module Name Hardware
MODULES="$MODULES tor2" # T400P - Quad Span T1 Card
# E400P - Quad Span E1 Card

MODULES="$MODULES wct4xxp" # TE405P - Quad Span T1/E1 Card (5v version)
# TE410P - Quad Span T1/E1 Card (3.3v version)

MODULES="$MODULES wct1xxp" # T100P - Single Span T1 Card
# E100P - Single Span E1 Card

MODULES="$MODULES wcte11xp" # TE110P - Single Span T1/E1 Card

MODULES="$MODULES wcfxo" # X100P - Single port FXO interface
# X101P - Single port FXO interface

MODULES="$MODULES wctdm" # TDM400P - Modular FXS/FXO interface (1-4 ports)
MODULES="$MODULES wcfxs" # either above or this

#MODULES="$MODULES wcusb" # S100U - Single port FXS USB Interface
#MODULES="$MODULES wcfxsusb" # either above or this

#MODULES="$MODULES torisa" # Old Tormenta1 ISA Card

MODULES="$MODULES ztdummy" # UHCI USB Zaptel Timing Only Interface

__________________ proc

This was in the bottom of my last post and I get the same result:

]# cat /proc/zaptel/*
Span 1: ZTDUMMY/1 "ZTDUMMY/1 1"

__________________

Thanks for taking a look!

Okay...so I'm still at a bit of a loss.

I made the changes you suggested and restarted. The X100P still won't pick up the line. Also of interest is that it's defined in outgoing and incoming...but only the SIP connection shows up in the Flash Operator Panel. Shouldn't I see this trunk as well?

After making the changes didn't seem to do it I ran genzaptelconf and it reverted the zaptel file to before the edits again.

I got this:

STARTING FOP SERVER
FOP Server Started
Chan Extension Context Language MusicOnHold
pseudo from-zaptel en

But now after the conf and a restart I do cat/proc and get:

# cat /proc/zaptel/*
Span 1: ZTDUMMY/1 "ZTDUMMY/1 1"

So it looks like running genzaptelconf messes that file up? So I'm not sure what to try next. I'd like not to have to revert to 2.8 but so far I can't get TrixBox to do anything with the card.

Hey,

I wanted to simplify so I recorded all my settings an re-installed. Actually I've re-installed 5 times now with different combinations of updating or not updating the system...

It seems TrixBox just plain doesn't like to have an X100P connection? It worked in Asterisk@Home 2.8 and it seems that Linux is seeing it fine. However, nothing I've tried will get it to be seen in Asterisk. I mean, I can create a Zaptel trunk and it shows it assigned to the incoming route...but even after the re-installs the trunk will never appear in the Flash panel and it will not answer calls. In 2.8 it showed up in the Flash panel and answered.

Any ideas? Based on a fresh install, or where I am currently, which is a fresh install and the update script how can I get a X100P to work with TrixBox?

Thanks. --I'm willing to re-install again if necessary. I don't mind if it breaks along the way (like after an update) after I get it seen...but it's amazingly difficult to get this thing working and it's kinda important that the box can actually answer a phone. :-)

My x100p works and is detected properly. I'm having terrible echoing and noise. I've tried 4 seperate cards (one of which is known to work flawlessly) and they have the same problem.

The cards worked fine with 2.8, but since using TB1.0 (after the updates), its having a terrible time. I really think it is something with the drivers.. but i don't know... I've tried seperate lines (a POTS line and a Vonage line and both have the same problem).

If I execute a rebuilt_zaptel, then a genzaptelconf, I noticed there was some errors in the text that went by so fast i almost didnt notice them at all,, I went back and ssh in with putty, so i could scroll back and copy paste it out, here is what i found,

on rebuild_zaptel

**********

Loading zaptel framework: [ OK ]
Waiting for zap to come online: [ OK ]
Loading zaptel hardware modules:
Loading tor2: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for tor2
[FAILED]
Loading wct4xxp: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wct4xxp
[FAILED]
Loading wct1xxp: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wct1xxp
[FAILED]
Loading wcte11xp: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wcte11xp
[FAILED]
Loading wcfxo: [ OK ]
Loading wctdm: [ OK ]
Loading wcfxs: [ OK ]
Loading ztdummy: [ OK ]
Running ztcfg: [ OK ]

****************

upon executing genzaptelconf, the following appears

*******************

Unloading wcfxs: ERROR: Module wcfxs does not exist in /proc/modules
[FAILED]
Loading zaptel hardware modules:
Loading tor2: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for tor2
[FAILED]
Loading wct4xxp: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wct4xxp
[FAILED]
Loading wct1xxp: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wct1xxp
[FAILED]
Loading wcte11xp: ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wcte11xp
[FAILED]
Asterisk Ready.
Asterisk Started

STARTING FOP SERVER
FOP Server Started
Chan Extension Context Language MusicOnHold
pseudo from-zaptel en
1 from-zaptel en
Verbosity is at least 1
Core debug is at least 1

*****************

so,, i dont know what to do about it, but maybe thats the same problem we all have.

anyone knows how to correct this, please share witt me

:pint:
Regards
Tom

OK, I ran through the steps again. My lovely x100p clone from DigitNetworks shows up as a Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface when I do an "lspci". In order to get it to work after installing the trixbox all I had to do was:

1) edit the file /etc/sysconfig/zaptel and comment out the line:

MODULES="$MODULES wcfxo" # X100P - Single port FXO interface
# X101P - Single port FXO interface

2) save it

3) next, I did a reboot, but I think doing a "modprobe wcfxo" would get the module loaded without having to reboot

4) last, run /usr/local/sbin/genzaptelconf

5) try it now
Not sure if it applies to the Motorola varieties. My clone card uses the Ambient chipset. Hope this is useful. -Neil

nmcg's fix above worked for me..

trixbox clean install, with meetme fixed, tiger jet card now answers

So far, my only solution has been,, to remove the card and not use it at all.

maybe after i get a couple more issues resolved with other components of my whole networking system, I will give that a try again.

Tom