Home » Forums » Community Edition » Trunks

Rhino R1T1 status LEDs

Undrhil
Posts: 264
 Member Since:
2006-06-25
Submitted by Undrhil on Mon, 02/18/2008 - 10:12am.

I have a Rhino R1T1 installed in my PC. As far as I can tell, all of the drivers installed properly; I can use 'cat /proc/zaptel/*' and it does list the Rhino card. I can use zttool and it shows the Rhino R1T1 card as Unconfigured. I can use ztcfg -vv and it shows

Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================

SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: Clear channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: D-channel (Default) (Slaves: 24)

24 channels to configure.

ZT_SPANCONFIG failed on span 1: Invalid argument (22)

...

So, to the LEDs on the back of the card. They are flashing Green (2), Red (4), which, according to the documentation, means something about the firmware loading. I haven't done anything with the firmware for this card and I wasn't even aware that the R1T1 had a variable firmware (unless it's part of the drivers downloaded through Yum.)

Speaking of yum, I have retrieved the latest driver version through yum:
rhino-2.6.18-53.1.4.el5.i386 2.2.3beta3-2 installed

‹ Trunk sequence seems not working hook flash an analogue x100p line ›

&nbsp

Undrhil
Posts: 264
 Member Since:
2006-06-25
OK, well, all of this
Mon, 02/18/2008 - 10:41am

OK, well, all of this appears to have been for naught. The card is showing a clean run condition now. Can that LED blink pattern stand for something besides loading a firmware module?

Anyway, now if anyone has any info on configuring the system to provide PRI trunks to a legacy PBX, I'd be most grateful. :)


&nbsp

kerryg
Posts: 6793
 Member Since:
2006-05-31
How are you connecting the
Mon, 02/18/2008 - 12:15pm

How are you connecting the trixbox system to the other PBX? Usually I use trixbox to provide SIP trunks to a legacy system by connecting the trixbox system to the legacy system via PRI lines.

--

Kerry Garrison
http://www.VoipStore.com - http://3cxbook.com
(888) VOIPSTORE - (888) 864-7786


&nbsp

Undrhil
Posts: 264
 Member Since:
2006-06-25
That is exactly what I am
Mon, 02/18/2008 - 12:38pm

That is exactly what I am trying to do. I am using a cross-over cable to connect my legacy PBX PRI card to the Rhino R1T1. I have actually gotten to the point where I can pick up on the PRI trunks and I get dialtone from my trixbox machine ... now I just need to know how to configure FreePBX to allow incoming calls to pass DIDs through to the legacy PBX.

I assume once I get dialtone from trixbox I can dial out using normal outbound rules in FreePBX, yes? I got the dialtone on the machine earlier and then I went to lunch ... gotta eat, you know? :)


&nbsp

Undrhil
Posts: 264
 Member Since:
2006-06-25
Routing calls from legacy PBX
Mon, 02/18/2008 - 1:17pm

OK, how do I make trixbox send the call from the legacy PBX out through my IAX2 trunks? Currently, any number I try to dial out from the legacy PBX goes through my Catch All Inbound Route (which I guess is technically what it's supposed to do, but how do I use this to send these calls out through my IAX2 trunks?)


&nbsp

Comment viewing options

Select your preferred way to display the comments and click "Save settings" to activate your changes.