Hello Everyone,
I am trying to track down an issue with my Sangoma A200D. When I pickup an analog line I hear a static/crackling sound. It is not consistent. When I as scanning my /var/log/message file I noted the following:
Aug 22 13:48:07 asterisk1 kernel: WANPIPE(tm) Hardware Support Module Stable 2.3.4-13 (c) 1994-2007 Sangoma Technologies Inc
Aug 22 13:48:07 asterisk1 kernel: Zapata Telephony Interface Registered on major 196
Aug 22 13:48:07 asterisk1 kernel: Zaptel Version: 1.2.19
Aug 22 13:48:07 asterisk1 kernel: Zaptel Echo Canceller: KB1
Aug 22 13:48:07 asterisk1 kernel: WANPIPE(tm) Interface Support Module Stable 2.3.4-13 (c) 1994-2007 Sangoma Technologies Inc
Aug 22 13:48:07 asterisk1 kernel: WANPIPE(tm) Multi-Protocol WAN Driver Module Stable 2.3.4-13 (c) 1994-2007 Sangoma Technologies Inc
Aug 22 13:48:07 asterisk1 kernel: wanpipe: Probing for WANPIPE hardware.
Aug 22 13:48:07 asterisk1 kernel: wanpipe: AFT-A200-SH FXO/FXS card found (HDLC rev.10), cpu(s) 1, bus #2, slot #4, irq #11
Aug 22 13:48:07 asterisk1 kernel: wanpipe: Allocating maximum 1 devices: wanpipe1 - wanpipe1.
Aug 22 13:48:07 asterisk1 kernel: WANPIPE: TDM Codecs Initialized
Aug 22 13:48:07 asterisk1 kernel: WANPIPE(tm) Socket API Module Stable 2.3.4-13 (c) 1994-2007 Sangoma Technologies Inc
Aug 22 13:48:07 asterisk1 kernel: NET: Registered protocol family 25
Aug 22 13:48:07 asterisk1 kernel: WANPIPE(tm) WANEC Layer Stable 2.3.4.13 (c) 1995-2006 Sangoma Technologies Inc.
Aug 22 13:48:07 asterisk1 kernel: wanec_create_dev: Registering Wanpipe ECDEV Device!
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Starting WAN Setup
Aug 22 13:48:07 asterisk1 kernel:
Aug 22 13:48:07 asterisk1 kernel: Processing WAN device wanpipe1...
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Locating: A200/400 card, CPU A, PciSlot=4, PciBus=2
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Found: A200/400 card, CPU A, PciSlot=4, PciBus=2, Port=0
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: AFT PCI memory at 0x48100000
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: IRQ 11 allocated to the AFT PCI card
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Starting AFT Analog Hardware Init.
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Enabling front end link monitor
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Global Chip Configuration: used=1
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Global Front End Configuraton!
Aug 22 13:48:07 asterisk1 kernel: wanpipe1: Configuring FXS/FXO Front End ...
Aug 22 13:48:08 asterisk1 kernel: wanpipe1: Module 0: Installed -- Auto FXO (FCC mode)!
Aug 22 13:48:08 asterisk1 kernel: wanpipe1: Module 1: Installed -- Auto FXO (FCC mode)!
Aug 22 13:48:08 asterisk1 kernel: wanpipe1: Module 2: Installed -- Auto FXO (FCC mode)!
Aug 22 13:48:08 asterisk1 kernel: wanpipe1: Module 3: Installed -- Auto FXO (FCC mode)!
Aug 22 13:48:10 asterisk1 kernel: wanpipe1: Module 4: DC-DC calibration has a surprising direct 107 of 0x01!
Aug 22 13:48:10 asterisk1 kernel: wanpipe1: Module 4: Installed -- Auto FXS!
Aug 22 13:48:12 asterisk1 kernel: wanpipe1: Module 5: Installed -- Auto FXS!
Aug 22 13:48:14 asterisk1 kernel: wanpipe1: Module 6: Installed -- Auto FXS!
Aug 22 13:48:15 asterisk1 kernel: wanpipe1: Module 7: Installed -- Auto FXS!
Aug 22 13:48:15 asterisk1 kernel: wanpipe1: Remora config done!
For some reason I have to run wancfg_zaptel to get a dial tone on the FXS ports.
Charles
Member Since:
2007-07-31